ScanIQ · Engineering|AIWarehouse · AI media & digital goods ↗

Scan in → scan out

Before & After

What went into ScanIQ and what came out: the phone photos on the mat, and the digital twins, printable models and solver results built from them. Every item states what was measured and what is still assumed.

Scan out: Monolith v3 body with lattice sleeves on the body and reservoir
Scan in: OEM YZ450F shock body on the mat, 262.00 mm by caliper
BeforeAfter

MAd hAT Monolith v3 shock body: Scan in: OEM YZ450F shock body on the mat, 262.00 mm by caliper → Scan out: Monolith v3 body with lattice sleeves on the body and reservoir

After: parametric grille guard, 3.5" DOM with upper struts
Before: 2021 F-250 after an elk strike (plate blurred)
BeforeAfter

F-250 elk strike → grille guard: Before: 2021 F-250 after an elk strike (plate blurred) → After: parametric grille guard, 3.5" DOM with upper struts

Scan out: STL opened in a phone 3-D viewer
Scan in: sprocket on the mat, 261.05 mm by caliper
BeforeAfter

Rear sprocket, caliper + mat: Scan in: sprocket on the mat, 261.05 mm by caliper → Scan out: STL opened in a phone 3-D viewer

Out: post frame, trusses and girts
In: 3-bed floor plan on a post-frame grid (posts 7.5' o.c. sides, 10' ends)
BeforeAfter

40×60 barndominium: In: 3-bed floor plan on a post-frame grid (posts 7.5' o.c. sides, 10' ends) → Out: post frame, trusses and girts

Diamond D gooseneck stock trailer (night capture)

[PHOTO] tires + axles[ASSUMED] box sizecapture check2026-10-25
BeforeScan in: 27 phone photos at night, 1/40 s at ISO 1000-2500
Scan in: 27 phone photos at night, 1/40 s at ISO 1000-2500
AfterOut: spec-anchored schematic twin (GLB/STL), not a photo reconstruction
Out: spec-anchored schematic twin (GLB/STL), not a photo reconstruction

21 of 26 photos were motion-blurred, so the 3-D reconstruction could only place 3 of them. ScanIQ's new capture check now catches this in about 6 seconds and tells you to reshoot in daylight, instead of failing an hour later. Measured from the photos: tire size 7.50R16LT (805 mm) and axle spacing 902 mm. Width, height and box length are Diamond D spec values, not measured.

MAd hAT Monolith v3 shock body

[CALIPER]voxel geometry2026-10-22
BeforeScan in: OEM YZ450F shock body on the mat, 262.00 mm by caliper
Scan in: OEM YZ450F shock body on the mat, 262.00 mm by caliper
AfterScan out: Monolith v3 body with lattice sleeves on the body and reservoir
Scan out: Monolith v3 body with lattice sleeves on the body and reservoir
AfterEye clocked 70° to OEM YZ450F (20° out of the reservoir plane)
Eye clocked 70° to OEM YZ450F (20° out of the reservoir plane)
AfterSide view: threaded body and lattice sleeve
Side view: threaded body and lattice sleeve

Generated geometry from the measured OEM body. Not yet built or flow-tested.

Rear sprocket, caliper + mat

[CALIPER][PHOTO]2026-10-22
BeforeScan in: sprocket on the mat, 261.05 mm by caliper
Scan in: sprocket on the mat, 261.05 mm by caliper
AfterScan out: STL opened in a phone 3-D viewer
Scan out: STL opened in a phone 3-D viewer

Flat symmetric part rebuilt as parametric CAD from the photo and caliper reading.

F-250 elk strike → grille guard

solver result[ASSUMED]Concept render2026-10-22
BeforeBefore: 2021 F-250 after an elk strike (plate blurred)
Before: 2021 F-250 after an elk strike (plate blurred)
AfterAfter: parametric grille guard, 3.5" DOM with upper struts
After: parametric grille guard, 3.5" DOM with upper struts
AfterDriver-side elk hit at the collapse load: peak stress at the upright/strut joint
Driver-side elk hit at the collapse load: peak stress at the upright/strut joint
AfterConcept render (generative) + 36-design sweep
Concept render (generative) + 36-design sweep
AfterThe damage it is designed to prevent
The damage it is designed to prevent

Beam-theory screening with assumed truck dimensions and elk mass; tape measurements pending. The truck image with the guard is a generative concept render, not a photo.

40×60 barndominium

parametric geometry2026-10-22
BeforeIn: 3-bed floor plan on a post-frame grid (posts 7.5' o.c. sides, 10' ends)
In: 3-bed floor plan on a post-frame grid (posts 7.5' o.c. sides, 10' ends)
AfterOut: post frame, trusses and girts
Out: post frame, trusses and girts
AfterOut: exterior, 40' × 60' × 10'
Out: exterior, 40' × 60' × 10'

Layout and framing study, not stamped drawings.

Carbon brake caliper guard

[PHOTO][ASSUMED]2026-09-16
BeforeScan in: phone photo on the ScanIQ mat (57 frames)
Scan in: phone photo on the ScanIQ mat (57 frames)
AfterScan out: v6 twin, watertight printable STL (rim Ø328 mm, 86 mm tall, 4 mm wall)
Scan out: v6 twin, watertight printable STL (rim Ø328 mm, 86 mm tall, 4 mm wall)
AfterModal check: first 4 modes, 164–387 Hz
Modal check: first 4 modes, 164–387 Hz

Thin-part planform + dish hybrid. Skirt, wall and total height are estimated, not measured: verify with calipers before use. Fit/pattern part, not a safety part.

KX250 52T rear sprocket

[PHOTO]solver result2026-10-22
BeforeScan in: phone photo on the ScanIQ mat
Scan in: phone photo on the ScanIQ mat
AfterScan out: measured parametric twin (STL)
Scan out: measured parametric twin (STL)
AfterStatic FEA on the twin: SF 5.91
Static FEA on the twin: SF 5.91

Flat symmetric part: fold + spec-anchored CAD rather than SfM. Center bore reads 136.65 mm from photos vs 133 mm by caliper: unresolved.

KYB PSF2 fork cap

[CALIPER][ASSUMED]2026-10-06
BeforeScan in: photo of the original cap
Scan in: photo of the original cap
AfterScan out: v2 model, Ø41.9 × 1.5 thread, stem OD 16 / ID 11
Scan out: v2 model, Ø41.9 × 1.5 thread, stem OD 16 / ID 11

Rebuilt from caliper readings plus photo segmentation. Older renders with the M46 × 1.0 thread were wrong and are not shown.

Rocker linkage

[PHOTO]solver result2026-10-09
BeforeScan in: rectified phone photo on the mat grid
Scan in: rectified phone photo on the mat grid
AfterScan out: 3-bore digital twin (STEP + STL)
Scan out: 3-bore digital twin (STEP + STL)

Rebuilt from photos after the part was gone. Frontal-view ratio metrology; some depths are assumed.

MAd hAT exhaust

acoustic model[ASSUMED]2026-09-21
Before

Input: bike and design parameters (bike.json). No SMX Spectroid sound capture is on file yet, so the target engine peaks are placeholders.

AfterOut: generated exhaust, CFD pressure drop 547.9 Pa
Out: generated exhaust, CFD pressure drop 547.9 Pa
AfterOut: acoustic transmission-loss baseline
Out: acoustic transmission-loss baseline

Phase 1 baseline. Re-run once a real sound capture is added.